![]() I read the link provided, which seems simple enough, but there's a fair number of commenters beneath it where it caused some sort of massive problem. Sorry for the delay, but frankly, I'm more than slightly terrified of what will happen if something goes wrong with the switch from RAID to AHCI. (ALL FILES DELETED!) After that's done, reboot normally and PC should boot from new SSD and HDD can be used for storage. If you don't boot via the F12 menu, PC will always boot from the old HDD.Īfter booting from SSD with HDD connected, use Disk Management to initialize the HDD. Power on and use the F12 menu to boot from the new SSD. If you want to use the old HDD for storage, reconnect it to the motherboard. Confirm the size of C: has increased and Windows and apps work properly. ![]() Reboot normally and it should boot from the new SSD. When all that's done, power off and unplug Macrium USB and external USB drive. That way you'll be able to resize C: to use whatever free space is still available after moving all the other partitions onto the SSD. Move the C: partition onto the new SSD last. Since the SSD is larger than the HDD, you want to reorder and resize the partitions. When Macrium loads, use it to "restore" the image saved on the external USB drive onto the new SSD. Plug the Macrium USB into PC with power fully off. Install the new SSD and disconnect the HDD from motherboard, to be safe. When the image is written and validated, use Macrium to create a bootable USB stick. And select Macrium's option to validate the image as soon as it's completed. Include all partitions that Macrium sees on the HDD in your image. Once the PC boots normally from the HDD with BIOS set to AHCI, install Macrium Reflect (free) and use it to image the boot HDD on an external USB drive. Reboot and Windows will automatically start with AHCI drivers enabled.Copy-paste this command, which will start Windows in Safe Mode the next time you reboot:īcdedit /set safeboot and press Enter.Open Cmd prompt window, run as administrator.To use the HDD for additional storage, reconnect the HDD, boot to the SSD using the F12 Boot Menu, then reinitialize the HDD using DiskPart and this procedure: īe sure to identify the HDD using the DiskPart command 'List Disk' and select the HDD using the DiskPart command ''Select Disk' before executing the other DiskPart - Configure Windows to to use AHCI this way: Note that the BIOS change is not made until you get to step 4.Ħ. Change SATA Operation in the BIOS from RAID to AHCI using this procedure: If you leave the HDD connected you will need to use the F12 Boot Menu to select SSD each and every time you wish to boot from the SSD.ĥ. ![]() Disconnect the HDD before booting from the SSD. You need to expand the OS partition before restoring partitions that follow the OS partition because you can only expand partitions that have unallocated space following that partition.Ĥ. When restoring the OS partition you will probably want the expand it since your new SSD is likely larger than your HDD. You can image each partition separately and then restore them to the SSD in the same order as on the HDD. Make sure to clone all the partitions on the HDD to the SSD. Clone your HDD to your SSD using Macrium Reflect Free Edition. Boot to your HDD using the F12 Boot Menu and select the HDD as the boot device.ģ. I miss the days when I could just boot off a floppy disk with, config.sys, and steps to follow:Ģ. I removed the SSD and everything's fine again, like nothing ever happened, but I can't clone my drive to the SSD unless I can actually boot my computer with the SSD in it. F8 didn't work, and I can't seem to access it any other way. I got into the BIOS, and it detects the SSD (and the original HDD), but when I get to the boot sequence instead of listing anything sensible like the olden days, it just says "windows boot manager", with no further information, nor any information about how to access this. I turned off my computer, put it in the slot, used the screw to anchor it, turned on the computer, and.it gave me a BSOD with something about a "kernel error" and lack of a bootable device. Bear in mind this is a blank SSD straight from Crucial, and I left my HDD in place and unaltered. I used Crucial's own SSD compatibility site and selected a Crucial P3 4TB PCIe M.2 2280 SSD. I decided to upgrade my XPS 8930 from a disk drive to an SSD.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |